728*90 Advertising Space
Home Depot Ratings and Reviews
Shop Now At Home Depot
Shop Caulk & Sealants or
Choose a Category
Home>

Customer reviews for 3 oz. Marine Adhesive Sealant

3 oz. Marine Adhesive Sealant

Stress caused by shock, vibration, swelling or shrinking is effectively absorbed. Check the bonding and sealing jobs this product can handle for you: fiberglass deck to fiberglass hull, wood to fiberglass, portholes and deck fittings, motors on fiberglass transoms, under moldings, hull seams above and below water line. Center board trunk joints. Between struts and planking, stern joints, deck housing, etc. Easy to apply with manual caulking gun. Remains workable with trowel or spatula up to 4 hours after application. Won't sag or flow in vertical or horizontal seams.
Overall rating:
5 / 5
5
 / 
5
(4 reviews) 4
Open Ratings Snapshot
100%of customersrecommend this product4 of 4reviews
Rating Breakdown 4 reviews
5.0 out of 5.0
5
(4)
4
(0)
3
(0)
2
(0)
1
(0)
Quality 
5.0 out of 5.0
5 out of 5
Value 
4.5 out of 5.0
4.5 out of 5
100%of customersrecommend this product4 of 4reviews
Customer reviews for 3 oz. Marine Adhesive Sealant
Review 1 for 3 oz. Marine Adhesive Sealant
from Raleigh, NC, USA
Age Range:45 to 54
,
Gender:Male
Home Improvement Profile:DIYer

Good boot adhesive

PostedOctober 4, 2012
Overall rating 
5.0 out of 5.0
5 out of 5
Quality 
5.0 out of 5.0
5 out of 5
Value 
4.0 out of 5.0
4 out of 5
The rubber soles of my boots were de-laminating from the leather body. I searched a few hiking forums, and 5200 was one of the recommended adhesives to repair it.
I can verify it works really well! I treated it like any other adhesive, including clamping it for 24 hours. Then went on a 20 mile hike, and all is well. It holds and it is waterproof.
Too bad the store doesn't carry the black color version. Also, a smaller package at a cheaper price would be nice for these one-shot jobs. But that's nit picking. It was still a lot cheaper than throwing the boots away or professional repair.
Pros: Very Adhesive, High Quality of Material
+5points
5out of 5found this review helpful.
Review 2 for 3 oz. Marine Adhesive Sealant
from Marion, NC

Mr

PostedOctober 27, 2010
Overall rating 
5.0 out of 5.0
5 out of 5
I have been using this product around the house and farm for over 7 years. It is remarkable! My first use of the product was when I discovered two lines leaking on my brother's hot tub. The tub had been installed in such a manner as to make it impossible to replace the plastic pipes unless the tub was completely disconnected and removed. Had to crawl into a very narrow space to apply. Tub was back in operation in 3 days and never leaked again. Since that time I have used it for numerous repairs of PBC pipe and fiberglass containers both in out buildings, portable equipment lines and on equipment cattle watering lines. It has enough flex and strength to withstand the bumping by cattle without breaking for long periods of time. The secret of the successful use, though, is always to allow more “set time” than indicated on the tube.
+8points
8out of 8found this review helpful.
Review 3 for 3 oz. Marine Adhesive Sealant

Removing 5200

PostedSeptember 22, 2012
Overall rating 
5.0 out of 5.0
5 out of 5
Quality 
5.0 out of 5.0
5 out of 5
Value 
5.0 out of 5.0
5 out of 5
Easy to remove. Use a heat gun to warm the part (if possible) then use the heat gun to heat the putty knife blade as hot as possible, Push the blade through the adhesive - reheat the blade and repeat as neded. That is how we boaters do it.
Pros: Very Adhesive, High Quality of Material, Easy to Use
+10points
12out of 14found this review helpful.
Review 4 for 3 oz. Marine Adhesive Sealant

PERMANENT!

PostedAugust 26, 2011
Overall rating 
5.0 out of 5.0
5 out of 5
3m makes 3000, 4000, 42000 and 52000. This is 5200, it is PERMANENT. do not use if you ever want to take something apart... ever! It is used to put the deck on hulls of boats! 95% of the time a consumer really wants 4000 or 4200, both are very strong but will come apart if need be. About the only way to get past 5200 once it has cured is with a piano wire saw, and that presumes you can get to it with a piano wire saw.
+6points
8out of 10found this review helpful.