The Bosch RA1181 Benchtop Router Table provides a premium large work surface for woodworking and routing. Designed to fit a variety of routers and able to mount on any workbench, this router table is a versatile piece of equipment that will serve as an indispensable part of any woodworking shop. And its 2-1/2 in. dust collection port offers better dust collection for a healthier work environment. The large aluminum top makes the table both durable and portable.
(41 reviews) 41
95%of customersrecommend this product37 of 39reviews
Rating Breakdown41 reviews
95%of customersrecommend this product37 of 39reviews
Delivery was on time and in good condition. Assembly was not difficult but as others have pointed out, only specific routers will fit the faceplate. I purchased a Porter-Cable that has a lift tool as optional. Used a drill press to easily make the necessary holes in the faceplate and it works great. Still need to build a permanent table to mount table but initial experience is a great table for the price.
Easy assembly with all the parts included. Make sure you have a compatible router or you will need an adapter base. I replaced a large router table with a precision fence that was more than I needed at this time. This is good for basic routing needs.
Fairly sturdy. Table is nice and flat. After careful adjustment, the router plate fits nice and flush.
(When moving it around, be careful not to dislodge the cover of the "storage area" on the side of the unit.)
I am quite satisfied with this purchase so far. I think it is a good product for the price. The construction quality is good and it is capable of a lot of adjustment. I do need to find a product to apply to the table face as the material does not slide very easily. I have a Milwaukee router that I attached to the table and I could not find anywhere that would tell me if my model would fit the table before I purchased it. In the end it did fit and the instruction manual does have my router listed in it but that would have been nice to find before I ordered it and sweated until I found out it would fit.
The table took a couple of hours to put together but the instructions are clear. I installed the Bosch 1617 2.25a router in this table. I am new to routers, but this appears to be a good combination. As the instructions state, the table should be secured by the front legs to a workbench or something sturdy, as it will tend to tip over backwords when routing larger pieces (found out by experience).
I just bought the table today and have a few comments. Commpared to the Ryobi Tables this one is far superior.
The Feather boards are sterdy and strong.
The plastic base looks cheap but is very stiff. My opinion having a large base to mount to a table beats the four point sheetmetal legs.
Took me 1hr to assemble and I consider myself to be very mechanial, just a lot of hardware. Router plate is very strong and takes a few minutes to level up.
The on off switch is small but in a beter location than the Ryobi. A very clever design.
The Brush steel top is very corse and has alot of mass.
The fense is made of an anodize extruded aluminum that is far superior to the Ryobi.
It comes with a side comparment that stores all the extra hardware and most accesories.
I would recommend this for the woodworker that wants something better than the a cheap "good value, good enough" version and the $900 Rockler "Superduper, do it all, digial, I want to be Norm Abram" version.
63out of69found this review helpful.
Review 7 for Router Table
A little getting used to but overall good product.
I bought this after a week of reading different reviews. It's a good value for the cost. Not to tricky to put together. I bought this not realizing that Rigid routers were not listed as "compatible" with the Bosch plate. Turns out it is compatible (Rigid 2hp 1/2 inch). The plate did't take me that long to level. "You must do this to cut reliable results." Don't rely on measurement markings on table, they are only good for making sure the guard is true. Instead, I use a square for depth and a test piece for height. The only design flaw I have seen is in the right side of the plastic base. I had to notch out some of the base so the adjustable guide could be easily removed.
7out of7found this review helpful.
Review 8 for Router Table
Much better than the other versions available here
Product is good, once you wax the table with some furniture paste.
Resolution of measuring lines could be greater- only marks every 8th of an inch. Makes it hard to get the fence perfectly straight.
Could use one additional throat piece. Currently there are three, which seem to range from small (good for 1/2 or below bits), large- good for bits up to 2", very large (up to 2 1/2, and no throat piece.
When using medium size bits, a lot of sawdust tends to fall down into the router.
I like the 3 1/2 inch opening, but when using a raised panel bit, a lot of sawdust tends to fall down into the router.
Overall, I'm much happier with this than the 99$ router table that is also offered.
There is only one shortcoming. The attachment of a Bosch router to the many-holed mounting plate was much less than easy in determining which screws and holes to use. One would think that this would be more clearly explained per router model, and MARKED on the aluminum mounting plate. It was the most lengthy part of the assembly, and I am not sure even now that it is right. Even still, It is a great little table, and I am getting the kinks figured out.
I bought this table for use with the Bosch 3.25 hp plunge router. The table is very sturdy, mounts to my workbench well with clamps or bolts, and has worked flawlessly so far. I've been very happy with this purchase. Received it very quickly and in good shape from Home Depot's web site.
This table is built solid. Really glad I made the right choice I debated awhile on this. Glade I spent a little more and got a good quality item. Bosch's service dept. is great. The inserts that go around the router bit had some of the tangs broke off. I called and they sent me new ones asap.
Pros: Durable, Easy to Use, Sturdy, Accurate, Good Size & Weight
I got this table mainly for the good materials the table top was made with: metal rather than mostly plastic. I have no complaints other than the 'storage' on the sides of the table are so easy to accidentally pull out that I've spilled all the contents out of it at least twice.
Excellent product, very easy to assemble and use. This is my first router table and I had no problems with use or directions. Setting up the router plate so it would be level is the most time consuming part, but is also the most important step. The aluminum table top is far superior to MDF and other similar type materials.
Pros: Durable, Easy to Use, Sturdy, Accurate, Long-Lasting
Ordering & delivery perfect. Packaging intact. Seems solid. Nice sized table. My Porter Cable 891 fit easily. The inset table has 8 leveling screws - doing all 8 at once is wrestling an octopus. Level with only the 4 corners in then remove the screws noting the corner they are in. Then level with only the 4 middle screws. Put the 4 corners back in and you should be good to go.