Looking for Answers about Quikrete 80 lb. Concrete Mix?

Customer questions and answers for
Quikrete 80 lb. Concrete Mix

Quikrete 80 lb. Concrete Mix can be used for building or repairing foundation walls, sidewalks, curbs, steps and ramps and for setting posts. This mix designed for pouring concrete 2 in. thick or more. Quikrete 80 lb. Concrete Mix consists of a uniformly blended, properly proportioned mixture of gravel, sand and Portland cement.
Customer questions and answers:
164 Questions
 | 
233 Answers
Overall rating:
4.714 out of 5
4.7
out of
5

Customer questions and answers for Quikrete 80 lb. Concrete Mix

Question

The ad says a discount is available for 82 sacks or more (2 pallets). What is the discount offered for plus 84?

Asked by
fxrupr
Dallas, Tx
about 80 lb. Concrete Mix on
January 8, 2014
0points
0out of 0found this question helpful.
Answer this question
2 answers
Answers
answer 1
Asked by
THDCustomerSupport
Kennesaw, GA
January 9, 2014
Thank you for your recent inquiry with The Home Depot. Because this item is only available in Home Depot stores, I believe the best advice would be to talk to one of our many specialty department professionals at your local Home Depot store. For any other questions, please visit your nearest local Home Depot store.
0points
1out of 2found this answer helpful.
answer 2
Asked by
QUIKRETEProductExpert
September 25, 2014
Please call your local Home Depot store for assistance.
-1point
0out of 1found this answer helpful.
Question

How many bags or concrete 80 pounds do I need to feel up 23' x 6' x 4" deep

Asked by
Rey73
Rex ga
about 80 lb. Concrete Mix on
May 2, 2014
0points
0out of 0found this question helpful.
Answer this question
2 answers
Answers
answer 1
Asked by
QUIKRETEProductExpert
May 8, 2014
An 80 lb. bag of QUIKRETE Concrete Mix yields approximately 0.6 cubic feet of concrete. To fill 23 ft x 6 ft x 0.34 ft (4 inch) would require approximately 47 cubic feet of concrete, or approximately 78 - 79 80 lb. bags of QUIKRETE Concrete Mix. Yields are approximate and will vary based upon waste, uneven sub-grade, etc.
+1point
1out of 1found this answer helpful.
answer 2
Asked by
ChrisFixit
May 5, 2014
Hello Rey73,

You will need 78 bags of 80lb concrete to fill the area. When calculating concrete the first step is to figure out the square footage using the formula of "length x width", in this case it being 138sq ft.

Quikrete has a number of product calculators on their site which are of great use here: http://www.quikrete.com/Calculator/...

I hope this helps.

Cheers,
Chris
0points
0out of 0found this answer helpful.
Question

How many 80 IB bags of Concrete will I need to do a 10 x 20 patio?

Asked by
Nick1
Lumberton Nc
about 80 lb. Concrete Mix on
April 17, 2014
0points
0out of 0found this question helpful.
Answer this question
2 answers
Answers
answer 1
Asked by
QUIKRETEProductExpert
April 21, 2014
A standard concrete slab is 4” (0.34 feet) thick. An 80 lb. bag of QUIKRETE concrete mix yields approximately 0.6 cubic feet. A 10 ft x 20 ft x 0.34 ft patio will require approximately 68 cubic feet of concrete, or approximately 114 80 lb. bags. Yields are approximate and will vary based upon waste, uneven sub-grade, etc.
+1point
1out of 1found this answer helpful.
answer 2
April 17, 2014
Figuring out a area of 10 feet by 20 feet by 4 inches thick, you need 100 bags of 80lbs, 134 bags of 60lbs, or 200 bags of 40lbs.
0points
0out of 0found this answer helpful.
Question

in 1 80 # bag of concrete mix, what is the volume of finish product ?

Asked by
cris
chicago
about 80 lb. Concrete Mix on
July 10, 2014
0points
0out of 0found this question helpful.
Answer this question
2 answers
Answers
answer 1
Asked by
QUIKRETEProductExpert
July 11, 2014
An 80 lb. bag of QUIKRETE Concrete Mix yields approximately 0.6 cubic feet of concrete. Yields are approximate and will vary based upon waste, uneven sub-grade, etc.
+1point
1out of 1found this answer helpful.
answer 2
Asked by
Blueridge
Blacksburg, VA, USA
July 15, 2014
An 80 pound bag yields approximately .6 cubic feet of product. A rough rule of thumb is that you need 150 pounds of concrete per cubic foot of your design. So, a walkway that is 4" thick, 4' wide and 8' long would be 18,432 cubic inches or 10.67 cubic feet, needing a rough estimate of 1,600 pounds of concrete.
0points
0out of 0found this answer helpful.
Question

How many 80 pound bag of concrete is needed to fill a 48 square feet form that is 2" deep?

Asked by
Backyard
Syracuse, New York
about 80 lb. Concrete Mix on
June 16, 2014
0points
0out of 0found this question helpful.
Answer this question
2 answers
Answers
answer 1
Asked by
QUIKRETEProductExpert
June 16, 2014
An 80 lb. bag of QUIKRETE Concrete Mix yields approximately 0.6 cubic feet of concrete. For a 48 sq. ft. slab that is 0.167 ft. (2 inches) thick, approximately 8 cubic feet of concrete, or approximately 13-14 80 lb. bags of concrete mix would be required. Note that a standard slab is typically 0.34 ft. (4 inches) thick, which would require twice as much concrete. Yields are approximate and will vary based upon waste, uneven sub-grade, etc.
+1point
1out of 1found this answer helpful.
answer 2
Asked by
Blueridge
Blacksburg, VA, USA
June 29, 2014
About 14 bags.
0points
0out of 0found this answer helpful.
Question

Can I mix sand with quikrete to make a base for the gravel between the rocks in my new patio?

Asked by
calgirl
Whitney, NE
about 80 lb. Concrete Mix on
July 14, 2014
0points
0out of 0found this question helpful.
Answer this question
2 answers
Answers
answer 1
Asked by
Blueridge
Blacksburg, VA, USA
July 15, 2014
No. Quikrete is premixed at the right ratio of portland cement, sand and aggregate. Adding more sand would change the ratio to the point where you would not get "concrete".
+1point
1out of 1found this answer helpful.
answer 2
Asked by
QUIKRETEProductExpert
July 16, 2014
The QUIKRETE® Concrete Mix is a preblended mixture of sand, rock, and cementitious materials. The addition of any materials beyond the specified water quantity will affect the properties of the mixture. This may not be the product that will best suit your needs, we recommend that you discuss your project with your local Home Depot representative at the Pro Desk or call QUIKRETE® directly.
0points
0out of 0found this answer helpful.
Question

Can i use it this in a fire place?

Asked by
ghaazi
frisco
about 80 lb. Concrete Mix on
May 25, 2015
The fireplace can reach a temperature of more than 900 C or 1650 F
0points
0out of 0found this question helpful.
Answer this question
2 answers
Answers
answer 1
Asked by
QUIKRETEProductExpert
May 27, 2015
No, Portland cement, the base material out of which standard concretes are made, can degrade in temperatures as low as 200 degrees F. Because of this, products used within the firebox of a fireplace, or near high temperatures, should be made of refractory cement, which is designed to be able to withstand exposure to high temperatures, rather than Portland cement. Only if the material is being used on the fireplace façade, far enough away from the firebox that it will NOT be exposed to these high temperatures, can the QUIKRETE® Concrete Mix be used.
+1point
1out of 1found this answer helpful.
answer 2
Asked by
CommunityAnswer
May 26, 2015
No, this concrete is not rated for use in a fireplace.
0points
0out of 0found this answer helpful.
Question

how many bags for a 29 ft x 20 ft, 4 inch deep cement pad?

Asked by
bbart
detroit, mi
about 80 lb. Concrete Mix on
August 4, 2015
0points
0out of 0found this question helpful.
Answer this question
2 answers
Answers
answer 1
Asked by
QUIKRETEProductExpert
August 11, 2015
Bbart, an 80 lb bag of QUIKRETE® Concrete Mix yields 0.6 cubic feet of concrete. An application that is 29 feet x 20 feet x 0.33 feet (4 inch) will require 193 1/3 cubic feet of concrete, or 322-323 80 lb bags of concrete. Yields will vary based upon waste, uneven subgrade, etc. It is crucial that you have sufficient equipment and man power to allow you to pour the entire application, or sections that are separated by expansion joints, before any of the material in that section has set. If some of the material sets before subsequent bags are poured, a cold joint will form. A cold joint is caused by the inability of the product to intermix between bags, and prevents the slab from being a single, solid mass. A cold joint may cause problems ranging from a simple aesthetic issue, to as serious as potentially allowing for water intrusion into the cold joint, which may eventually lead to concrete degradation. Please contact the QUIKRETE® Technical Center directly at 1-800-282-5828 if you have any further questions.
+1point
1out of 1found this answer helpful.
answer 2
Asked by
CommunityAnswer
August 5, 2015
It will take you 325 bag of this size for your project.
-1point
0out of 1found this answer helpful.
Question

How many bags of concrete will i need to fix my stairs?

Asked by
vader
Kansas City
about 80 lb. Concrete Mix on
June 27, 2013
I have a walk way that is cracking. The walk way is 3.5ft.x15ft.x2in. How many bags of concrete will I need to fix them?
0points
0out of 0found this question helpful.
Answer this question
1 answer
Answers
answer 1
Asked by
QUIKRETEProductExpert
June 28, 2013
It is not clear if you plan on removing the existing walkway in its entirety, or whether you simply have areas that need repairs. An 80 lb bag of QUIKRETE Concrete Mix yields approximately 0.6 cubic feet of concrete. To replace the walkway in its current dimensions would require between 8 to 9 80 lb bags. Sidewalks are more commonly 4 inches thick, which would require 17.5 80 lb bags. These estimates are approximate, and will vary based upon waste, uneven subgrade, etc. If you instead plan on repairing the walkway, depending upon the damage, different products will be appropriate for repair. QUIKRETE Vinyl Concrete Patcher is designed for making repairs to small areas of concrete surfaces which are cracked, chipped, or spalled. It is not intended to be used for deep patches or large areas. QUIKRETE Commercial Grade FastSet Repair Mortar is a polymer modified, rapid setting repair material specially formulated to make structural repairs to any concrete or masonry surface, horizontal or vertical. It can be built up to at least 1 ½” in a single application. Once you make the necessary repairs, you may consider top coating the entire walkway (while maintaining the control joints) with QUIKRETE Sand / Topping Mix. If the majority of the area will require an application that is at least 1 inch thick, it is suggested that QUIKRETE Bonding Adhesive be used to coat the clean, unsealed, prepped surface before applying the Sand/Topping Mix. If the majority of the area will require an application that is less than 1 inch thick, it is suggested the QUIKRETE Concrete Acrylic Fortifier be blended with the Sand/Topping Mix, to replace a portion of the water, before applying the Sand/Topping Mix to the clean, unsealed, prepped surface.
+1point
1out of 1found this answer helpful.
Question

How many 80lb. Bag of quikcrete are needed for 16' feet long and width 4' feet and to dig 5" inch

Asked by
Friend
Denver
about 80 lb. Concrete Mix on
July 1, 2013
0points
0out of 0found this question helpful.
Answer this question
1 answer
Answers
answer 1
Asked by
QUIKRETEProductExpert
July 2, 2013
An 80 lb bag of QUIKRETE Concrete Mix yields approximately 0.6 cubic feet of concrete. To pour a 16 ft x 4 ft x 5 inch (0.42 ft) volume, will require approximately 27 cubic feet of concrete, or 45 80 lb bags. This estimate is approximate, and will vary based upon waste, uneven sub-grade, etc.
+1point
1out of 1found this answer helpful.
Question

Can you dump dry concrete mix into the form and then add water?

Asked by
horseshoefoo
about 80 lb. Concrete Mix on
August 20, 2013
+1point
1out of 1found this question helpful.
Answer this question
1 answer
Answers
answer 1
Asked by
QUIKRETEProductExpert
August 21, 2013
No, this method should only be used with QUIKRETE Fast-Setting Concrete Mix #1004-50 when installing posts.
+1point
1out of 1found this answer helpful.
Question

How many cubic feet does one 80 pound bag of quickrete contain?

Asked by
Larry
about 80 lb. Concrete Mix on
October 13, 2013
0points
0out of 0found this question helpful.
Answer this question
1 answer
Answers
answer 1
Asked by
QUIKRETEProductExpert
October 16, 2013
An 80 lb bag of QUIKRETE Concrete Mix yields approximately 0.6 cubic feet of concrete when mixed with water. This is an estimate and will vary based upon waste, uneven sub-grade, etc.
+1point
1out of 1found this answer helpful.
Question

how much coverage do i get out of one 80 pound bag?

Asked by
josh
about 80 lb. Concrete Mix on
December 21, 2013
0points
0out of 0found this question helpful.
Answer this question
1 answer
Answers
answer 1
Asked by
QUIKRETEProductExpert
December 23, 2013
An 80 lb. bag of QUIKRETE Concrete Mix yields approximately 0.6 cubic feet of concrete. This is an estimate and will vary based upon waste, uneven sub-grade, etc.
+1point
1out of 1found this answer helpful.
Question

How many 80# bags would I needto set 18 post 2ft in ground?

Asked by
prntruss
Cheyenne Wy
about 80 lb. Concrete Mix on
January 19, 2014
0points
0out of 0found this question helpful.
Answer this question
1 answer
Answers
answer 1
Asked by
QUIKRETEProductExpert
January 20, 2014
The number of bags required to set 18 posts 2 feet into the ground will depend upon the diameter of the posts, as well as the diameter of the holes. It is recommended to place 1/3 of the length of the post in the hole, so a 2 foot deep hole would be appropriate for a post that is 6 feet long. The typical recommended diameter of the hole is 3 times that of the diameter of the post. For example, if the diameter of the post is 2 inches, the recommended diameter of the hole is 6 inches. A single 2 foot deep hole that is 6 inches in diameter, for a post 2 inches in diameter will require approximately 0.6 80 lb bag, or 10.8 bags for 18 holes. A single 2 foot deep hole that is 9 inches in diameter, for a post 3 inches in diameter will require approximately 1.3 80 lb bags or 23.4 bags for 18 holes. A 2 foot deep hole that is 12 inches in diameter, for a post 4 inches in diameter will require approximately 2.3 80 lb bags or 41.4 bags for 18 holes. These are estimates, and will vary based upon waste, variation in diameter, etc.
+1point
1out of 1found this answer helpful.
Question

how many sq ft do i get of a 80 pd bag at 3 in deep

Asked by
salau
chicago
about 80 lb. Concrete Mix on
April 29, 2014
0points
0out of 0found this question helpful.
Answer this question
1 answer
Answers
answer 1
Asked by
QUIKRETEProductExpert
May 1, 2014
An 80 lb. bag of QUIKRETE Concrete Mix yields approximately 0.6 cubic feet of concrete. An application that is 0.25 ft (3 in.) deep, will cover approximately 2.4 square feet. Yields are approximate and will vary based upon waste, uneven sub-grade, etc.
+1point
1out of 1found this answer helpful.
Question

How many bags of Quickrete would I need for 10x10 feet, 4 inches thick?

Asked by
hottub
Montpelier, VA
about 80 lb. Concrete Mix on
September 21, 2014
0points
0out of 0found this question helpful.
Answer this question
1 answer
Answers
answer 1
Asked by
QUIKRETEProductExpert
September 23, 2014
An 80 lb. bag of QUIKRETE Concrete Mix yields approximately 0.6 cubic feet when placed. A slab with dimensions 10 ft. x 10 ft. x 0.34 ft. (4”) will require approximately 34 cubic feet of concrete, or approximately 57 80 lb. bags of Concrete Mix. Yields are approximate and will vary based upon waste, uneven sub-grade, etc.
+1point
1out of 1found this answer helpful.
Question

Is this OK to use for installing an in-ground basketball hoop?

Asked by
Bob
about 80 lb. Concrete Mix on
April 13, 2013
0points
0out of 0found this question helpful.
Answer this question
2 answers
Answers
answer 1
Asked by
travelinPOP
on road - Cascade Mountains
April 14, 2013
It should work fine. I use these for setting satellite dishes. Your hole must be deep enough to keep the post straight and below the frost line. Your hoop should include recommendations for the size and number of sacks.rv
0points
0out of 0found this answer helpful.
answer 2
Asked by
QUIKRETEProductExpert
April 16, 2013
Yes, QUIKRETE Concrete Mix may be used for installing an in-ground basketball hoop. We would recommend waiting 3 – 7 days before placing any stress / strain on the newly placed concrete.
0points
0out of 0found this answer helpful.
Question

Time

Asked by
CSCHLAUD
New Ulm
about 80 lb. Concrete Mix on
June 18, 2013
How long does this concrete take to set/dry? Meaning how long until I would be able to attach rails and pickets to a post I set in this concrete?
0points
0out of 0found this question helpful.
Answer this question
2 answers
Answers
answer 1
Asked by
star
June 25, 2013
It is set within 6 hours. If you live somewhere the wind doesn't blow and you pour the concrete early in the am, by evening you could build the fence. Personally, I would wait at least 24 hours. Pam
0points
0out of 0found this answer helpful.
answer 2
Asked by
QUIKRETEProductExpert
June 21, 2013
It is recommended that you wait a minimum of 24 hours before subjecting the post to any strain when QUIKRETE Concrete Mix #1101 is utilized to set the post.
0points
0out of 0found this answer helpful.
Question

bonding addive

Asked by
tinygeorge
lenox,mi
about 80 lb. Concrete Mix on
August 9, 2013
would i make the concrete bond better to odd surface of driving?
0points
0out of 0found this question helpful.
Answer this question
2 answers
Answers
answer 1
Asked by
DesigningWoman
August 13, 2013
Hello tinygeorge and thank you for your question.

You will need to have a raw concrete surface before adding the Quikrete 80 lb. Concrete Mix (Model # 110180). If you are working on a painted or stained surface, remove the paint or stain before proceeding. If that is not possible, paint Quikrete 1 qt. Bonding Adhesive (Model # 99) over the surface using a paintbrush. Allow to set up for 1-2 hours before pouring the new concrete.

Best wishes on your project.
 
Products related to my answer
 
0points
0out of 0found this answer helpful.
answer 2
Asked by
QUIKRETEProductExpert
August 15, 2013
Yes, QUIKRETE Concrete Bonding Adhesive is designed for use to bond new concrete, plaster or stucco to existing concrete, plaster or stucco to improve the bond. Use it to coat the existing clean, unsealed, prepped concrete surface before applying the new concrete. Note that sidewalks and driveways are standardly broom finished - the broom finish roughness provides traction when wet.
0points
0out of 0found this answer helpful.
Question

how many bags for 9'x10'x3"

Asked by
shedbuilder
about 80 lb. Concrete Mix on
August 11, 2013
0points
0out of 0found this question helpful.
Answer this question
2 answers
Answers
answer 1
Asked by
DesigningWoman
August 13, 2013
Hello shedbuilder and thank you for your question.

You will need 38 bags of the Quikrete 80 lb. Concrete Mix (Model # 110180) to complete your project.

Best wishes on your project.
0points
0out of 0found this answer helpful.
answer 2
Asked by
QUIKRETEProductExpert
August 15, 2013
One 80 lb bag of QUIKRETE Concrete Mix yields approximately 0.6 cubic feet. For a 9 ft x 10 ft x 0.25 ft slab, approximately 22.5 cubic feet or 37.5 80 lb bags of Concrete Mix would be required. Note that slabs are typically 4 inches deep. For the same area but 4 inches thick, approximately 30 cubic feet or 50 80 lb bags of Concrete Mix would be required. Yields are approximate and will vary based upon waste, uneven sub-grade, etc.
0points
0out of 0found this answer helpful.
« 1 2 3 4 5  ... 9 »